Concrete Products by Eastern Tank & Utility Services, Inc.

3, 4 & 4.5 cu yd

Which Municipal Hopper Spreader Will Work For You?

 General:
• Self contained hopper
• Spreads free flowing materials sand and/or salt
• Spread width of 4' to 30'
Material hopper:
• 12 gauge 304 Stainless steel with continuously welded seams.
• All hopper sides are formed with a continuous "J" channel profile for added rigidity and strength. Six (6) 12 gauge body gussets.
• Optimum material feed is maintained by hopper side walls slopped at 45°
• Heavy duty, 4 section hinged top grate is standard. Bars are ¼" diameter located on 3" center grid (installed).
• Built-in four corner lift loops.
Conveyor:
• Conveyor is 12½" wide, all steel pintle chain type (#667H Pitch), with 1/4" x 1" crossbars on 4-5⁄8" centers.
• Replaceable 10 gauge stainless steel chain shields.
• Replaceable 10 gauge stainless steel conveyor floor.
• 10 gauge stainless steel inverted Vee
• Conveyor driven by 20:1 ratio worm gearbox utilizing tapered bearings
• Conveyor chain is adjustable for chain take up, providing optimum performance and drive life.
• Chain drive and idler sprockets are 6-tooth cast sprockets keyed to 1¼" shafts.
• Conveyor chain wiper minimizes waste.
Spinner Assembly:
• Spinner chute has two adjustable internal baffles
• Four (4) external baffles (3 adjustable, 1 fixed)
• 18" x ¾" thick polyurethane spinner disc
• Bolt-on spinner housing minimizes replacement cost.
Power Source:
• Gas Engine: 10.5 horsepower, Briggs & Stratton Intek
Optional Equipment:
• Nylon strap mounting kit
• Tailgate latch kit
• Liquid spray systems, electric
• Stainless Steel D.O.T. Spreader Lightbar
Dimensions:
• 3 cu. yd. – Overall Length, 96"; Width, 70"; Height, 45"; Recommended use, dump bodies and flat beds with a GVW chassis of 15,000 to 26,000 lbs.

7, 8, & 9 CUBIC YARD STAINLESS STEEL SALT & SAND SPREADERS

Which Municipal Hopper Spreader Will Work For You?

Ideal for heavy duty municipal and commercial applications.

Designed for municipalities and contractors with a minimum 26,000 lbs. GVW chassis.

General:
• Self-contained hopper.
• Spreads free flowing materials sand and/or salt.
• Spread width of 4’ to 40’.

Material Hopper:
• 7-gauge 304 stainless steel cross members.
• 10-gauge 304 stainless steel, long sills with rear enclosure & integral chain shields.

• 10-gauge 304 stainless steel replaceable floor.
• 10-gauge 304 stainless steel sides (continuously welded seams), gussets and rear panel.

• 10-gauge 304 stainless steel front panel.
• Four (4) 5/8” thick lift points.

Feedgate:
• 10-gauge, 304 stainless steel with scaled screw jack adjustment.
• 18-5/8” wide x 10” tall opening.

Conveyor:
• 24" wide, pintle chain conveyor with 3/8” thick x 1-1/2” wide crossbars on 4-1/2” centers (667X Pitch).
• 2" diameter drive shaft with 4-bolt relubeable bearing.

• 8-tooth cast iron sprockets.

• 50:1 or 25:1 direct-drive gearbox with extended through-shaft for ground speed sensor.

• 1-1/2” diameter idler shaft with 4” adjustable range relubeable bearing.
• Conveyor chain wiper made of belted rubber minimizes waste.

Standard Installed Equipment:
• 4-section hinged top grate screens. 3/8" diameter bar on 3" centers with 1/4" x 2" x 2" angle iron frame. Hinged to 6" horizontal crossbeam.
• 10-gauge, 304 stainless steel inverted “V” prevents material compaction and reduces wear on drive train components.

Chute/Spinner Assembly:
• 10-gauge, 304 stainless steel laser cut parts with smooth radius corners.

• Telescopic adjustment in 3” increments to accommodate varying body mounting heights.

• Two (2) adjustable, internal baffles direct material to 20” diameter x 5/8" thick, 6-fin poly spinner disc.
• Three (3) adjustable external and one (1) fixed deflector with overlapping corners provide a precision spread pattern.

• Top-mounted, direct-drive hydraulic spinner motor provides better ground clearance and corrosion protection.

• Two (2) stainless steel spring latches quick release hinged chute for bulk material unloading and convenient ground storage.

Power Source:
• Hydraulic Drive: Two independent direct drive hydraulic motors (17 GPM @ 1,500 PSI).

Optional Equipment:
• Dump Body Tailgate Latch Kit (Part # 3008560).

• DOT Spreader Lightbar (Part # LB8663SST). 8" Tall x 66" Long x 3" Deep stainless steel lightbar includes 9 mounting holes for 4” recessed stop-turn-taillights-strobes and 2-1/2" marker lights.
• Liquid Spray System (Part # LS4), 104 Gallons.
• Tie-Down Kit (Part # 3010548).

Dimensions:
• Hopper length, 120”; Overall length, 143"; Width, 82”
• Recommended use, dump bodies and flat beds with a minimum 26,000 lbs. GVW chassis.


Which Municipal Hopper Spreader Will Work For You?

Stainless steel hopper spreaders for municipalities and contractors with a minimum 34,000 GVW chassis. These spreaders include two independent direct drive hydraulic motors.